+90 212 222 87 80 nokta@noktaelektronik.net

B2B Вход Техническая служба

upTech

8 ports 10/100M POE Switch with 2 Gigabit Uplink ,IEEE802.3af/at,120W

Name: 8 ports 10/100M POE Switch with 2 Gigabit Uplink ,IEEE802.3af/at,120W
Brand: upTech
SKU: SW108FGP-A

Артикул: SW108FGP-A

Варианты

3 вариантов

Power120 W3

Port Count8 Port3

Сейчас показан: SW108FGP-A · 120 W · 8 Port

Connects PoE cameras and access points to a Gigabit backbone.

8 PoE+ ports carry data and power together over a single CAT5e or CAT6 cable, and 2 Gigabit uplink ports connect the switch to the network backbone. Auto-detection determines the PoE requirement, the speed and the duplex mode of the powered device on its own.

10 Port8 PoE+ and 2 Gigabit uplink

120 WTotal PoE budget

30 WMax. PoE output per port

5.6 GbpsBandwidth

250 mPoE distance in Extend mode

-10°C ~ 45°COperating Temperature

Key features

30W

PoE+ output per port

It delivers 30 W per port to IEEE 802.3at powered devices and 15.4 W to IEEE 802.3af devices.

250m

Extend mode stretches the reach

With the DIP switch in Extend position, port speed drops to 10 Mbps and the switch carries PoE up to 250 meters.

5.6Gbps

Switching bandwidth

It works with a 2K-entry MAC address table and a 4.16 Mpps packet forwarding rate.

1000Mbps

Uplink speed

Ports 9-10 run at 10/100/1000M with auto-negotiation.

220V AC

Built-in power supply

It draws AC220V at 50/60 Hz from the mains and works with ±4 KV DC surge protection.

IN DAILY USE

No configuration neededIt works plug and play and asks for no management interface or setup software.

Fewer cables to pullCameras, IP phones and wireless access points need no separate outlet; power travels on the data cable.

Contains broadcast stormsVLAN mode isolates the ports from each other, so broadcast traffic from one camera does not reach the others.

ApplicationsIP cameras·WLAN access points·IP phones·Office access control systems

Network Specifications
PoE Port Priority	Supported
Bandwidth	5.6Gbps
MAC Address Table	2K
Diagnostics
LED Indicators	• PWR (Power indicator), PoE (PoE indicator), Link/Activity (Link/activity indicator) • Extend Mode: Constantly On • Uplink: Constantly on when ports 9-10 are active; blinking indicates good data communication status. • Link: Constantly on when ports 1-8 are active; blinking indicates good data communication status.
Power Supply
PoE Standard	IEEE802.3 af/at
PoE Power Output (Per Port)	AF: 15.4w (IEEE 802.3af) AT: 30w (IEEE 802.3at)
Power Consumption	5W
Total Power	125W
Dimensions and Weight
Weight	0.4kg
Dimensions	203mm x 140mm x 44.5mm (W×D×H)
Environmental Conditions
Operating Temperature	-10°C ~ 45°C
Storage Temperature	-20°C ~ 70°C
Operating Humidity	5% ~ 95% Non-condensing
Storage Humidity	5% ~ 95% Non-condensing
Other Specifications
PoE	1-8 ports: 10/100M Auto-Negotiation RJ45
Uplink	9-10 ports: 10/100/1000M Auto-Negotiation RJ45
Maximum PoE Output Power	30W
PoE Power Budget	120W
PoE Transmission Distance	CAT6, 100m
Operation Mode	Store-and-Forward
Transmission Mode	IEEE802.3X Full Duplex and Backpressure Half Duplex
DIP Switch	Standard Mode 100m, VLAN + Extend Mode Selection 250m
Packet Forwarding Rate	4.16Mpps
Supported Cables	UTP CAT5E or higher
DIP Switch	• VLAN • Extend
Input Voltage	AC220V. 50/60Hz
Surge Protection	±4KV DC
IEEE 802.3af	Power over Ethernet
IEEE 802.3at	Power over Ethernet Plus
IEEE 802.3x	Flow Control
IEEE 802.3	10BASE-T
IEEE 802.3u	Fast Ethernet 100Base-TX
IEEE 802.3ab	Gigabit Ethernet 1000Base-T
IEEE802.3az	Energy Efficient Ethernet (EEE)

Datasheet

SW108FGP-A

pdf10/7/2022

Sertifika

CE RoHS Sertifikası

v1.0pdf9/29/2022

Fotoğraf

SW108FGP-A

jpg8/26/2025